网站公告:

产品中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:http://www.debradjwhite.com

业内资讯

当前位置:首页 - 新闻中心 - 业内资讯 - 气体增压泵对的适应在于一

气体增压泵对的适应在于一些细节的处理

发布时间:2018-06-15 17:38:54   发布人:http://www.debradjwhite.com
安装:安装过程中,要避免杂物进入出口,保持出口清洁。
Installation: during the installation process, avoid debris entering the exit and keep the exit clean.
驱动气体:请使用清洁的气源,以保证泵能持续稳定的工作,驱动气体要求颗粒<5um,建议在泵的驱动口加配二连体,泵在装配时,所有运动部分已经抹有适量润滑油,一般不再需要润滑,如长期使用干燥的压缩气体驱动,建议在二连体的油杯内加入适量的润滑油,进行油雾润滑。
Driving gas: please use a clean gas source to ensure that the pump can continue to work steadily and drive gas to require particles < 5um, recommended to add two conjoined in the pump's drive port. When the pump is assembled, all the parts of the movement have been applied with a proper amount of lubricating oil, and generally no need for lubrication, for example, the long use of dry compressed gas drive. Add the right amount of lubricating oil to the two linked oil cup to lubricate the oil mist.
连接管路:根据泵的输出压力,请选择合适的出口连接管路,确保承受泵的最大输出压力。
Connecting pipe: according to the output pressure of the pump, please select the appropriate outlet connection pipe to ensure the maximum output pressure of the pump.
气体增压泵
气体增压泵入口压力:入口压力越大,流量也随之增大,单级增压泵,需要一定的预压才能达到理论最大输出压力。双级增压泵,入口压力要求1-10bar,入口压力不允许超过10bar,建议<8bar。确保泵的使用寿命。
The inlet pressure of the gas booster pump: the greater the inlet pressure, the increase of the flow, and the single stage booster pump, which requires a certain prepressure to reach the maximum theoretical output pressure. Two stage booster pump, inlet pressure 1-10bar, inlet pressure is not allowed to exceed 10bar, recommended < 8bar. Ensure the service life of the pump.
启动:该泵的最小驱动压力为1.5-2bar,可通过调整二连体调压阀调节驱动气体的压力,以达到你所需要的压力。
Starting: the minimum driving pressure of the pump is 1.5-2bar, and the pressure of the driving gas can be adjusted by adjusting the two body regulating valve to achieve the pressure you need.
接口尺寸很重要:请确认所安装的螺钉和管是否适合泵的范围,为保证液泵能获得理想的流量和压力,不能减少泵的尺寸。
The interface size is very important: please confirm that the installed screws and tubes are suitable for the range of the pump to ensure that the pump can get the ideal flow and pressure, and can not reduce the size of the pump.
气体增压泵的操作温度:标准温度范围为-20度到80度,采用VE密封材质的液泵最大操作温度可达60度,短时操作时,最大操作温度可达80度。
The operating temperature of the gas booster pump: the standard temperature range is -20 degree to 80 degrees, the maximum operating temperature of the liquid pump with VE sealing material can reach 60 degrees. The maximum operating temperature can reach 80 degrees in short time operation.
如在户外为0度或低于0度的情况下可提供特殊的密封介质。
If the outdoor is 0 degrees or less than 0 degrees, special sealing medium can be provided.
推荐驱动空气质量:根据PNEUROP (欧洲增压器,真空泵和气驱工具制造委员会)推荐代号611/1948的规定,驱动气体为3-4个质量级别。
Recommended drive air quality: according to PNEUROP (European turbocharger, vacuum pump and gas drive tool manufacturing Committee) recommended code code 611/1948, driving gas to 3-4 quality levels.
颗粒最大颗粒5纳米 最大颗粒浓度 5毫克/立方米
The maximum particle size is 5 nm, and the maximum particle concentration is 5 mg / m3.
露点+10度=含水量9.4克/立方米 +2度=含水量5.6克/立方米
Dew point +10 = water content 9.4 g / cubic meter +2 = water content 5.6 g / cubic meter.
含油量1.0-5毫克/立方米
Oil content 1.0-5 mg / m3
注意:当使用湿气或高度湿气时会产生结冰现象,建议在此情况下在空气驱动管线上安装一个水分离器或干燥器。如果驱动空气过于干燥且露点低于-40度,建议使用油雾器。选用优质的驱动气体能够延长液泵的密封件使用寿命。
Note: when moisture or high humidity is applied, ice will occur. It is suggested that a water separator or dryer be installed on the air driven pipeline in this case. If the drier air is too dry and dew point is below -40 degrees, it is recommended to use an oil mist. The use of high quality driving gas can extend the service life of the sealing parts of the liquid pump.
 

13188935873

qq

推一把28推百度