网站公告:

产品中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:http://www.debradjwhite.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题 - 小型气体增压泵实现流量的

小型气体增压泵实现流量的最大化的方式

发布时间:2018-08-06 16:35:59   发布人:http://www.debradjwhite.com
小型气体增压泵参数:
Small gas booster pump parameters:
增压介质:各种无腐蚀性洁净气体。
Supercharging medium: all kinds of non corrosive clean gas.
最高增压压力:80MPA。
Maximum pressure pressure: 80MPA.
单台最大流量:1200L/min(也可多台并联流量更大)。
The maximum flow rate of a single station is 1200L/min (or multiple parallel flows).
单台最大耗气量:900L/min。
The maximum air consumption of a single station: 900L/min.
驱动压力要求:2-8bar(6-8bar最佳驱动)。
Drive pressure requirement: 2-8bar (6-8bar best drive).
小型气体增压泵得结构和材质:
The structure and material of the small gas booster pump:

气体增压泵

小型气体增压泵总体分为增压部分,驱动部分和控制部分。增压部分部件大致有,前后增压端盖铸钢,双层增压缸缸筒内304外铸钢,1套单向阀有密封垫.弹簧.钢珠.单向阀内外壳体等组成,U型冷却管铝合金,增压活塞和活塞杆密封圈等一系列组成增压部分。驱动部分大致有,前后端盖铸钢,驱动缸筒铝合金,前后撞针304钢材和密封圈(功能铺助控制部分换向),高低压换气钢管304材质,驱动活塞和活塞杆密封圈等一系列组成驱动部分。控制部分大致有驱动腔体铸钢,换向阀分为外阀套和内阀芯有铝合金和密封圈组成。
The small gas booster pump can be divided into the pressurization part, the driving part and the control part. The pressurized parts are roughly composed of the cast steel, the 304 outer cast steel in the double pressurized cylinder cylinder, the 1 sets of one-way valves with seal pads, the spring, the steel ball and the inner and outer shell of the one-way valve, the U type cooling pipe aluminum alloy, the pressurized piston and the piston rod seal ring, etc. The driving parts are roughly as follows: the front and back cover cast steel, the cylinder tube aluminum alloy, the front and back 304 steel and the seal ring (the function transfer control part), the 304 material of the high and low pressure air exchange steel pipe, the driving piston and the piston rod seal ring, etc., are made up of a series of driving parts. The control part is mainly driven by cavity casting steel, and the reversing valve is divided into outer valve sleeve and inner valve core with aluminum alloy and sealing ring.
气体增压泵的流量与多种因素有关,驱动气压、入口压力、管径,管阻等有关系
The flow rate of gas booster pump is related to many factors, such as air pressure, inlet pressure, pipe diameter and tube resistance.
1,气体增压泵的驱动气压越高,那么输出的压力越高,他的流量越大。
1, the higher the driving pressure of the gas booster pump, the higher the output pressure, the greater the flow.
2,入口压力的高低决定了泵的输出流量,一般来讲泵的入口压力越高,他的输出流量越大。
2, the level of inlet pressure determines the output flow of the pump, generally speaking, the higher the inlet pressure of the pump, the greater the output flow.
3,管径,在一定压力的情况下,管径的粗细也决定了气体增压泵的流量。
3, pipe diameter, under a certain pressure, the diameter of the pipe also determines the flow of the gas booster pump.
4,管道越长,泵的压力及流量都会有相应的减少,管阻是其中的影响因素。
4, the longer the pipeline is, the lower the pressure and flow rate of the pump will be.
此外,影响气体增压泵的流量与泵自身的因素也有关系,例如缸径,及泵体内部的单向阀通径等等因素。
In addition, the flow rate of the gas booster pump is also related to the factors of the pump itself, such as cylinder diameter, and the one-way valve diameter inside the pump body and so on.
感谢您的阅读,此文的文章来源:气体增压泵更多的内容和问题请点击:http://www.debradjwhite.com 我们会继续努力的为您提供服务,感谢您的支持!
Thank you for your reading, the source of this article: more content and problems of gas booster pump please click: http://www.debradjwhite.com we will continue to work hard for you to provide service, thank you for your support!

13188935873

qq

推一把28推百度